Selected articles for topic: rfid 125 khz arduino

→ 12 articles

Check also 2 Videos for this topic

RFID 125 kHz Module for Arduino, Raspberry Pi, Intel ...

The RFID 125 kHz Module can be used with an Arduino , Raspberry Pi , Intel Galileo or Waspmote microcontroller, and therefore allows you to carry out projects using RFID technology no matter which programming board you choose!

Arduino and Raspberry Pi RFID Module: your own...

Website: https://www.generationrobots.com

GitHub - Wookai/arduino-rfid: A short example of how to ...

README.md

#arduino-rfid

A short example of how to read 125 kHz RFID tags using an Arduino and a RMD6300 RFID module

See a video here on how it works in action [Youtube] ( http://www.youtube.com/watch?v=u8YD3-BrHv0 )

Required hardware

Breadboard, cables, LEDs

How to use

Simply plug the antenna, as well as the power, ground and TX pins of...

Website: https://github.com

125 kHz RFID reader with Arduino - Arduino Stack Exchange

��

�

While this is supporting material, you have three answers here none of which answer the actual question which was asked. At the very least you should be combining them. -� Chris Stratton Aug 4 '14 at 1:15

��

�

So If they mean about circular...

Website: https://arduino.stackexchange.com

Stupid Simple Arduino LF RFID Tag Spoofer -Use Arduino for ...

RFID tags are all over the place. �They're used in building access control systems, passports, inventory tracking . . . � This instructable will show how you can use an Arduino and a few simple components (wire coil, transistor, capacitor, resistor) to make a device that can spoof an 125 KHz (low frequency) RFID tag. �This is version 1, so there are many enhancements that can be made, but...

Website: http://duino4projects.com

Raspberry Pi RFID Shield, 125 kHz - microcontrollershop.com

The RFID Shield for Raspberry Pi consists of two components: An RFID Module and the Raspberry Pi to Arduino Connection Bridge that contains an XBee socket into which the RFID Module will connect.

The picture shows these...

Website: microcontrollershop.com

Connecting 125Khz RFID module to arduino – Part 1 ...

Connecting 125Khz RFID module to arduino - Part 1

Author tasos Published on

A-H-A-Project-RFID

In this tutorial we will see how we can connect a RDIF reader into arduino.

We are going to use a�125 Khz RFID module� that can be bought from seeedstudio.

Some 125 Khz tags are also needed. We bought them from ebay but you can also find them on other online shops.

This guide is the first of a...

Website: http://www.hw2sw.com

Diy rfid reader antenna TurkHub.net

GAO RFID's UHF 860-960 MHz 4 Port Long Range RFID Reader features a compact size, light weight and multi-regional flexibility. It has 4 antenna ports and is ...

Video

Playing with Radio Frequency Identification readers & writers Check out more of my Arduino & Electronics...

Website: http://turkhub.net

rfid - how to detect 125khz tags with mfrc 522 - Arduino ...

up vote 0 down vote

You can buy a 125 kHz reader from eBay for around $7. I got one like this:

You can communicate with it (listen to it) with a single serial...

Website: https://arduino.stackexchange.com

RFID 125 kHz Module for Arduino, Raspberry Pi, Intel ...

I have read and I accept the privacy policy(*)

In order to comply with the provisions in Spanish Data Protection Act (L.O. 15/1999 of 13th December) and its implementing Regulation (R.D. 1720/2007, of 21st December), LIBELIUM hereby informs its Customers and websites users that any personal data supplied through the forms contained in its websites shall be recorded in a file named...

Website: cooking-hacks.com

Tahoe Designer | HOW TO: Simple Arduino LF RFID Tag Spoofer

This instructable will show how you can use an Arduino and a few simple components (wire coil, transistor, capacitor, resistor) to make a device that can spoof an 125 KHz (low frequency) RFID tag. �This is version 1, so there are many enhancements that can be made, but this version is stupid simple, yet it works. �I did this in a few hours without much previous knowledge of RFID and...

Website: http://tahoedesigner.com

GitHub - miguelbalboa/rfid: Arduino RFID Library for MFRC522

The SDA pin might be labeled SS on some/older MFRC522 boards.

Hardware

There are three hardware components involved:

Micro Controller:

An Arduino or compatible executing the Sketch using this library.

Prices vary from USD 7 for clones, to USD 75 for "starter kits" (which might be a good choice if this is your first exposure to Arduino; check if such kit already includes the Arduino, Reader, and...

Website: https://github.com

RFID Reader ID-12LA (125 kHz) - Cooking Hacks

RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-12LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing. Power the module, hold up a 125kHz card, and get a serial string...

Website: cooking-hacks.com

12 Resources