Use Arduino and RS232 Shield to interface Integrated UHF ...

Food

Long Range UHF RFID reader (1-6M) (ISO18000-6C EPC G2) integrates

the reader with the antenna. After first powered on, the reader will buzz once to indicate that it starts to work. When there is tag approaching the reader, it will buzz to indicate that it's sending the data. For the same tag, the read interval can be configured. After read, if the same tag is still in the read area,...

Date: 2015-03-31 16:20:54
Website: http://diyourself.ru

UHF RFID Reader Antenna (902-928MHz, 8dBic LHC Pol)

Cannot Obtain Cable to Connect to Cottonwood RFID Board

Posted by Unknown on 20th Jun 2014

I contacted LinkSprite and explained that I needed to connect the 8 dBi antenna to the Cottonwood Long Range UHF RFID reader UART (ISO18000-6C EPC G2) and then ordered the antenna and adapter cable.

The adapter...

Website: http://store.linksprite.com

Arduino Uno & UHF RFID Reader - forum.linksprite.com

I am trying to control the Cottonwood UHF RFID reader with an Arduino Uno.

I am currently testing for simple communication between the devices, by turning the antenna power on and off.

According to the datasheet, the reader must receive 18 03 FF to turn on the antenna power, and the reader will respond with 19 03 FF.

Here is my code

�

I have Tx of the Uno connected to Rx of...

Website: http://forum.linksprite.com

LinkSprite UHF RFID Reader Antenna (902-928MHz, 8dBi RHC Pol)

Product Description

SAFETY

The antenna should be mounted permanently and securely on a mounting panel in accordance with all installation instructions.

�

LOCATION

For best results, point the antenna towards the center of the coverage area. A line-of-sight path between the antenna and active...

Website: http://store.linksprite.com

Long Range Integrated UHF RFID reader (1-6M) (EPC G2)

LinkSprite Integrated Long Range RFID reader (1-6M) (ISO18000-6C EPC G2): typical 2-3M

In the far-distance RFID system, the ID tag has much less energy compared to that of the reader. This imposes a very high requirement on the reader's receiver sensitivity. In LinkSprite's far-distance RFID system, the receiving and transmitting paths are separated, and using different frequencies. Normally, the transmitting power is between 100mW~500mW.

LSID-0702 has the feature of multiple-protocols, fast response...

Website: http://www.ezshopfun.com

Cottonwood: UHF Long distance RFID reader module ...

Programming

Arduino sample code for Xbee UHF RFID Reader Tutorial (Arduino issues scan commands)

/* � The circuit: * LCD RS pin to digital pin 12 * LCD Enable pin to digital pin 11 * LCD D4 pin to digital pin 5 * LCD D5 pin to digital pin 4 * LCD D6 pin to digital pin 3 * LCD D7 pin to digital pin 2 * LCD R/W pin to ground * 10K resistor: * ends to +5V and ground * wiper to LCD VO...

Date: 2017-01-11 09:16:06
Website: http://www.linksprite.com

Long Range Integrated UHF RFID reader Ethernet (1-6M) (EPC G2)

If you want to back order when the stock is 0, please contact� orders@linksprite.com .�

�

inkSprite Long Range RFID reader with Ethernet RJ45 port (1-6M) (ISO18000-6C EPC G2): typical 2-3M.

�

In� the far-distance RFID system, the ID tag has much less energy compared to that of the reader. This imposes a very high requirement on the reader's receiver sensitivity.� In�LinkSprite's��far-distance RFID system, the receiving and transmitting paths are separated, and using different frequencies.� Normally, the transmitting power is...

Website: http://store.linksprite.com

7 Resources